The thermo-vacuum press of a suitcase type – FMGroup PV-2412 is intended for the industrial enterprises which are manufacturers of furniture.

With the help of the offered equipment it is possible to face furniture facades, and also manufacture of overlays on doors and plat bands. For lining can be used a variety of plastic films or classic veneer. In addition, on sale there is a more advanced model with a specialized lifting table.

Advantages of thermo-vacuum press PV-2412

A big advantage is that lift of the thermo module is provided with the help of special gas stops. In most models of presses, the module is lifted using a conventional winch, which is unsafe, and can lead to worker injuries and damage any expensive equipment.

Press thermo-vacuum PV-2412 has a special clamping frame, due to which the number of clamps decreases. When the clamping frame is used, the production process is seriously increased and the probability of obtaining rejects is reduced when facing with films of different thicknesses.

The frame of the thermo-vacuum press is a quality welded metal profile. During welding, the geometry of the structure is completely controlled. In addition, after the end of welding, the metal structure is covered with a special paint, resistant to physical influences. In order to fix the press stably, it is equipped with special supports. Thanks to the supports it is possible to fasten the press on an uneven surface, with a height difference of up to 60 millimetres.

Quartz lamps are used for heating elements, which are mounted on special ceramic insulators. The whole heating circuit is designed in such a way as to maximize the heating of the wood and at the same time to have a simple and maintainable design. This means that this is an excellent opportunity for a thermovacuum press to buy at the best price.

---

---

Reliable Accessories

Pump station based on vacuum pump BBH 1.5. The tank with water is united in one design with the pump, therefore water leakage is excluded, the exhaust system is improved, stability of work is increased. This is not an expensive solution, increasing the productivity of the pumping station.

To measure the operating temperature, it is used without a cabinet, without an inertial temperature sensor, which provides an accurate temperature control of the process, improving the quality of products, reducing the amount of waste and energy costs.

To measure the depth of vacuum, an electronic vacuum gauge pressure transducer is used, it allows to accurately control the depth of the vacuum and specify this parameter using a microprocessor vacuum gauge. And it also allows the vacuum station to operate automatically (maintaining the required vacuum depth), that helps reduce wear of the vacuum pump, save energy, improve product quality, reduce waste, simplify settings and operate. Other manufacturers use electro-contact vacuum metric gauges that are prone to such defects as sticking of contacts (the pump operates constantly without switching off), incorrect activation of contacts (the pump does not turn on when the vacuum falls – the entire tab of the blanks and film is damaged), not the accuracy of the readings.

In the press, KGT quartz lamps installed on ceramic insulators (insulators have practically unlimited service life) are used as heating elements. The installation scheme of the heaters is carefully designed for maximum effective and uniform heating of the film, which ensures easy replacement, availability, low cost.

Ease of management and control

The control panel of the press is designed on the basis of standard industrial automation units. As a thermo-regulator and a vacuum gauge, microprocessor regulators of the domestic production of the company “OWEN” are used, which has proved itself in the market (simplicity of repair, availability, absence of problems with warranty and availability of spare parts). Also digital shutter timers of the Delta company were used to set the extractions of the pressing process in automatic mode. A fully automatic pressing cycle is realized, where the operator only needs to set parameters, put the workpiece and press the “START” button. The process of tightening or manufacturing the facade will go off-line (the number of defects decreases, productivity increases, the cost of production decreases). A solid-state relay is used to control the heaters, which eliminates voltage surges and electrical interference during operation, which is especially important for enterprises suffering from a shortage of power supply.

The presence of inspection windows made of hardened, trauma-safe, heat-resistant, tinted glass in the thermo module allows for visual control of the pressing process. Accelerates the process of development in the production of new products and materials, reduces the probability of rejection in production.

The control panel with large buttons and switches is intuitively clear. Digital displays for monitoring temperature and vacuum depth with large LED indicators for easy reading of necessary information. The process of adjusting the temperature and the depth of the vacuum is fully automated. All this makes the work on the press more convenient.

You can get advice from our specialist on all matters of interest by ordering a callback. You can also buy a thermo-vacuum press with a lifting table at a perfect price.